heading


C-System

SFL (Above Lickerin)

Stationary flats are designed from coarser PPSI - bottom to Finer PPSI - top gives excellent pre opening of heavier fibre tufts. Mote knife and suction device removes trash particles and even distribution of fibres.

SFL (Above Lickerin)

Salient Features

  • Machine originality will be maintained during modification.
  • Imported high quality Stationary Flat Tops wires ensures yarn sliver quality and consistency in life.
  • It gives good parallelization of fibres and results reduces the carding strain and increases the life of cylinder wire and revolving flats.
  • Sturdy AI. base beam with Individual adjustment of Stationary Flats and mote knife makes accurate gauging which helps carding quality and production at higher speeds.
  • Smooth finish suction device helps to remove micro dusts, short fibres and motes and help to maintain clean suction in the machine.
  • No gap between each flat prevents dust liberation.No need for sticking forms between each flat.
  • Big suction device prevent air curling which ensures no suction chocking during card running.
  • Aluminium flats are made out of alloy grade smooth finish extrusion materials which gives flat stability.


SFD (Above Doffer)

Finer PPSI stationary flats, mote knife and smooth finish suction device helps to improve classimate results.

SFD (Above Doffer)

Salient Features

  • Machine originality will be maintained during modification.
  • Imported high quality Stationary Flat Tops wires ensures yarn sliver quality and consistency in life.
  • It gives good parallelization of fibres and results reduces the carding strain and increases the life of cylinder wire and revolving flats.
  • Sturdy AI. base beam with Individual adjustment of Stationary Flats and mote knife makes accurate gauging which helps carding quality and production at higher speeds.
  • Smooth finish suction device helps to remove micro dusts, short fibres and motes and help to maintain clean suction in the machine.
  • No gap between each flat prevents dust liberation.No need for sticking forms between each flat.
  • Big suction device prevent air curling which ensures no suction chocking during card running.
  • Aluminium flats are made out of alloy grade smooth finish extrusion materials which gives flat stability.


Pre Opening Combing Segments - (Economic)

Pre Opening Combing Segments - (Economic)

Salient Features

  • Construction of assembly is replaceable slide (strip) type.
  • Economic replacement for conventional araldite and punched sheets combing segments.
  • Sharp points gives better pre-openings that results in minimum loss of good fibres.
  • Aluminium combing bars are made out of alloy grade smooth finish extrusion materials which gives flat stability.
  • Machine original mote knives can be fixed without any alterations in assembly.
  • Easy replaceable and cost economic during replacement time.


Pre Opening Combing Segments - (Individual Gauging)

Pre Opening Combing Segments - (Individual Gauging)

Salient Features

  • Construction of assembly is individual gauge setting and replaceable slide (strip) type.
  • Individual gauge setting ensures accurate gauging which results in better opening of fibre tuffts in lickerin zone.
  • Sharp points gives better pre-opening that results in minimum loss of good fibres.
  • High quality hardened mote knives help to remove smaller and heavier trash particles results good reduction of neps in lickerin zone.
  • Easy replaceable and cost economic during replacement time.
  • Made out of high grade individual flat aluminium bars which gives more stability to ensure accurate gauging.

Suitable: D-K715, D-K740, MK4 & MK5


RSK Pin Beater Segments

RSK Pin Beater Segments
Sanmit Model
RSK 1200
RSK 1600


Salient Features

  • Designed with two pin beater segments and two perforated Control sheets to ensure removal of heavy trash and impurities with the help of gentle fibre tufts opening.
  • Easy replaceable with two slotted perforated control sheets which reduces fibre rupture and good fibre loss.
  • Ensures cleanng efficiency upto 20%.
  • Ensures consistent fibre tuft quality in blow room machines.

Suitable: Open end & Fine spinning


F - Flats / K - Knife
Card ModelAbove Doffer (SFD)Above Lincker-in (SFL)Pre Opening Combing Segments(Under Lickerin)Process
D-K715 & D-K7405 F + 1 K + Suction7 F + 1 K + Suction4 Segments + 2 KCotton
D-K715 & D-K7409 F11 F4 Segments + 2 KSynthetic
D-K760 D-K780,
D-K800 & D-K803
(Single Licker in)
6 F + 1 K + Suction8 F + 1 K + Suction - Cotton / Synthetic
D-K803 & D-K903 (3 Licker-in - Twin Flat)6 F + 1 K + Suction6 F + 1 K + Suction - Cotton / Synthetic
D-K706 (Cast Iron base C-System)6 F + 1 K + Suction7 F + 1 K + Suction - Cotton / Synthetic
MK - 36 F + 1 K + Suction12 F + 1 K +Suction - Cotton / Synthetic
MK - 4 & MK - 56 F + 1 K + Suction8 F + 1 K + Suction4 Segments + 2 KCotton / Synthetic
C4 & C104 F + 1 K + Suction8 F + 1 K + Suction - Cotton / Synthetic
C50 & C517 F + 1 K + Suction7 F + 1 K + Suction4 Segments + 2 KCotton / Synthetic
300, 300A,300A - V3 & 300A - V45 F + 1 K + Suction - Economic ModelCombing Segment Full SetCotton / Synthetic
C .1/2, C.1/2a, C 1/3, (Economic model)6 F + 1 K + Suction3 FEconomic Model Combing SegmentFull SetCotton / Synthetic
Chinese - FA2017 F + 1 K + Suction11 F + 1 K +Suction - Cotton
Chinese - FA1865 F12 F - Synthetic
HOWA - CMS80 HOWA-CMSK3 / Toyoda-Meikin6 F12 F - Synthetic
Toyoda - Meikin6 F + 1 K + Suction - - Cotton


5 Flats + 1 Mote knife conversion suitable for : 300, 300A, 300A V3, 300A V4

Upgrade your Carding Machine to acheive

 

  • IPI Reduction Minimum - 10% to Maximum 20%.
  • Clasimate Improvement ( A1 & A2 fault) upto 20% from Existing Quality.

 

Results will achieved on Identical Testing Conditions on Same Carding Machine ( Before & After )